Loading...

Home > Hot Tub > Spa Display Not Working

Spa Display Not Working

Contents

Matt Giovanisci Have you checked to see if it's a bad control panel? Click for more information. did they use the gecko system , that sounds really really high for the board...get your control system info get on the ineternet check out some spa parts sites . Most people are not that adventurous though.

When I Do Push A Selected Button, Something Else Comes On The issue is most likely a faulty topside control by moisture entering the topside. One more step Please complete the security check to access www.justanswer.com Why do I have to complete a CAPTCHA? Janis Cuthbertson first I cleaned the filters then I replaced them still says flo Matt Giovanisci You may need to call a professional to take a look at your pump. This will tell. http://www.doityourself.com/stry/troubleshooting-hot-tub-control-panel-problems

Hot Tub Control Panel Not Working

What could have happened? See if the panel or any buttons are cracked or if it could have possibly gotten wet. I switched the spa off at the mains This morning I switched the spa back on and today there is no cycling down- the temperature shows 32 degrees celsius, and then

My spa, and most others, have an electrical outlet attached to the spa pak. I'm no expert but it looks as though it is more than just condensation as some copper wires have green/blue scale on them. If the breaker does not trip after unplugging the pump, ozonator or blow, you’ve found the problem and you can now replace that component. Hot Tub Lights Not Working hope this helps.

Where will i find the control system info so i can look around on the net? Top Side Control Panel Not Working My filter after two days was really dirty I guess from rain and no cover. Troubleshooting Tips For Hot Tubs With A Circuit Board If your spa does not have a circuit board, click here for mechanical troubleshooting. KungFuMaintenance 36,826 views 8:34 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Duration: 9:09.

He should stop being so helpful. Hot Tub Troubleshooting No Power Put filter in it ran about 6 minutes. Popular Articles From Our Workshop Hot Topics: Hot Tub Fuses Hot Topics: Hot Tub Fuses Pools, Spas, Hot Tubs & Saunas Troubleshooting Common Problems with Hot Troubleshooting Common Problems with Hot Most hot tubs come with adjustable jets that can be turned down for less water flow, or closed completely.

Top Side Control Panel Not Working

I haven't heard back from them yet in regards to the mother was repairable or not!

I ran it without filter and it ran for hours no problem. Hot Tub Control Panel Not Working Sign Up All Content All Content This Topic This Forum Advanced Search Browse Forums Blogs Calendar Staff Online Users More Activity All Activity Search More More More All Activity Home Hot Hot Tub Control Panel Blank Does anybody have any ideas?!

Look in the heater if possible as well. I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah any ideas what else I can check. Yes i certainly won't be in any rush to spend the $1100. No Display On Hot Tub

You should contact a Jacuzzi specialist. Matt Giovanisci Sounds like you have an issue with your pump. If so, the pressure switch or the pressure switch cable is defective and should be replaced. I can't seem to find anyone else here in Sydney who sells Arctic spas.

Matt Giovanisci At this point I would just call someone. Hot Tub Buttons Not Working Professional help is normally required if replacing the pump does not remedy the problem. If you are at an office or shared network, you can ask the network administrator to run a scan across the network looking for misconfigured or infected devices.

Watch Queue Queue __count__/__total__ Find out whyClose # 36 Why doesn't my hot tub work softcellelectrical SubscribeSubscribedUnsubscribe5,6895K Loading...

Derek January 14, 2014 Reply That did it! The pump has to be running for your spa to heat, so if the pump does not come on the problem may be with pump itself. Both mean the same thing and will be troubleshot the same. Hot Tub Control Panel Codes Here is a contact for a company that is servicing our product in your area.

ThankHeather on Customer FeedbackThanks to Matt & Richard for the EXCELLENT customer support and spa advice. Bri M I went to clean hot tub today. Please refer to this link to confirm that it was wired properly. I have all the paperwork and purchase receipts but unfortunately the dealer, hear in Sydney folded through the recession ( Oh the recession which we avoided here in Australia, *just rolling

If the water is cool, the high limit sensor is bad and needs to be replaced. Shut off the breaker. Don't worry, you will not get shocked as the pins are low voltage. What could be causing this Ken Johnson I overfilled my tub the other day.

Strange Messages If the display is showing strange messages or blinking several lights at once, there may be a software problem or a problem with the circuit board. The controller is a Gecko TSC-14 SL-ADB-BF2-CE. PoolAndSpaCentre 20,860 views 13:42 Hot Tub Not Hot Enough? 104° Temperature Override (:1:) Sundance Spas pre-2009 - Duration: 5:41. If you have a intermittent fault then it maybe moisture at the PCB connection, dry it out, this may easily sort the problem.

We will not be held liable for any injuries that may result from the troubleshooting or installation of any electrical components in your hot tub spa unit.Safety is key when servicing And my heater either. Sign in to make your opinion count.

© Copyright 2017 philgiebler.com. All rights reserved.