Loading...

Home > Hot Tub > Spa In A Box Heater Not Working

Spa In A Box Heater Not Working

Contents

Randy Simmons Is there a blower on the spa? Matt Giovanisci Sounds like you have an issue with your pump. Make sure the filter is properly seated in the housing and that the o-ring is properly seated in the o-ring groove. 7. Prove trigonometric identity under given conditions What specifically did Hillary Clinton say or do, to seem untrustworthy to Americans?

Make sure the hose washers are in place and seated inside the connections. Here are my thoughts: Makse sure the thermostat is set higher than 70 degrees. I used the potentiometer trick, it worked great!!!!!ReplyDeleteAnonymousMay 28, 2011 at 9:38 AMi see an old set of darts in the picture.. When I called Blue Ridge I was told there was a wheel inside the heater that needed to be turned to reset the thermostat. http://www.leicesterhottubhire.co.uk/Spa-n-a-box-fault-finding.htm

Hot Tub Not Heating Troubleshooting

Look on the underside of the black power pack. Disconnect the plug from the receptacle until the fault has been identified and corrected. 9. It is either plugged into an ungrounded outlet or it is doing it's job and sensing a short to ground, or may be defective and needs to be replaced. My GFCI is Tripping If your GFCI is tripping, it could be due to a bad heater element, pump, blower or ozonator.

Will post if I have any success.ReplyDeleteAnonymousNovember 15, 2011 at 6:11 AMI posted on 10/26 looking for 2 STG1120. Was told try removing pressure switch and blow thru itBe sure no obstructions. All rights reserved. Spa N A Box Replacement Power Pack Your heater burned up from being exhausted from running with the top off.

Storing: The spa may be stored in its original box. Spa N A Box Replacement Parts On top is a 6" polished aluminum cylinder with a 1/2" inlet hose on the pump side bottom and another 1/2" outlet hose at the top on the opposite side. Voltage must be constant in and out of the appliance. http://diy.stackexchange.com/questions/7411/troubleshooting-a-hot-tub-spa-that-wont-heat-up My Pump is Making Loud Noises If your pump is louder than it used to be, the bearings in the motor are going out and soon the motor will seize.

AVERTISSEMENT: AVANT D'UTILISER UN SPA OU UNE CUVE THERMALE, MESUREZ LA TEMPERATURE DE LEAU A L'AIDE D'UN THERMOMETRE PRECIS WARNING: WATER TEMPERATURE IN EXCESS OF 98.6°F (38°C) MAY BE INJURIOUS TO Hot Tub Heater Reset Button Tried to swap with my old power pack sensors and did, even though the threading is totally different. Fix it yourself for 30$http://www.spadepot.com/shop/Hi-LimitTemp-Sensor-Assembly-for-Balboa-M-7-Systems-32016-P9700C704.aspxReplyDeleteBillJanuary 11, 2011 at 9:21 AMNice link. Close air valve, plug GFCI back into outlet.

Spa N A Box Replacement Parts

DO NOT BYPASS GFCI WITH STANDARD PLUG !!! It may seem cumbersome, but it DOES get easier each time you go it. Hot Tub Not Heating Troubleshooting Tacticalterry Do u have two pumps? Hot Spring Spa Heater Reset Button Your cache administrator is webmaster.

I can reset it after about 30 minutes and it stays on until the next day around the same time. Tweet Share53 Pin110 Share34Shares 197 This Is The Last Hot Tub Manual You Will Ever Need You'll save at least $100 off the bat with this easy-to-follow digital handbook. This is d-i-y-able stuff if you're comfortable working around electrical circuits, but got to be very careful. Pool Care Hot Tub Care Resources Search 5 Common Hot Tub Issues and Solutions Download our FREE guides and receive new posts every week. Hot Tub Not Heating Up Enough

What is strange about this system however is that both sensors are right next to each other with no component in between them. If your contactor is 120 volts (see coil info on the side of contactor) then this is what you should be reading, the same applies for 220 volts Mentioned above are Place your hand in front of lower water return inlet inside tub to see if there is good water flow. And about the heater and chasing the line to find the problem.

Also one sensor's resistance jumped a magnitude of 100x when submerged in water, and the other didn't. Hot Tub Not Heating After Refill Seal it up tight with the cover on and the heat set as high as possible. WARNING: DO NOT USE DRUGS OR ALCOHOL BEFORE OR DURING THE USE OF A SPA OR HOT TUB TO AVOID UNCONSCIOUSNESS AND POSSIBLE DROWNING.

The two small hand tight connections leading to the spa are leaking: There is a garden hose washer on the inside of each of these connections.

H. The time now is 03:37 PM. Power Pack should be sent to Service Center for inspection / repair. Hot Tub Heating Slowly Giving me a headache lol!

If you still experience a problem, call the dealer or the manufacturer. There is also a reset button on the top of the digital panel, did you try pushing that? If the bromine level has not increased to the ideal 3-5 ppm range, punch another hole in the bottom of the feeder and retest after another 2 days. spa is set in the heater/filter cycle and water is flowing from the jets), the first thing you will look for is the Hi-Limit Switch, also referred to as the heater

They provided me with a part number: stg-1120, $26.50, I ordered two. Hold for 15 seconds, then pull finger back apx. 1/2" and see if you feel a quick short pulse of warm water. Have you confirmed this part works?ReplyDeleteAnonymousJanuary 22, 2011 at 2:03 AMHi,Does anyone have any pictures on how to remove these censors, clean and replace them ?ReplyDeleteAnonymousJanuary 22, 2011 at 6:09 AMI The final thing it could be, without getting further complicated, is the hi-limit switch is faulty and needs to be replaced.

Remove filter lid and check or replace filter lid gasket, make sure lid is tight and NOT cross-threaded GFCI Problems !!!! as a condition of their listing of this product.

© Copyright 2017 philgiebler.com. All rights reserved.