Loading...

Home > Hot Tub > Spa Jets Not Working Properly

Spa Jets Not Working Properly

Contents

Just enough to let some water or air out. You could simply drain and refill and see if that solves your problem. THANKS in advance! Düşüncelerinizi paylaşmak için oturum açın. http://philgiebler.com/hot-tub/spa-not-working-properly.html

In some spa systems, when you completely drain the spa, air gets trapped in the pipes and equipment. I have seen this problem most often in gunite spas. Air. How did you fix this Reply With Quote 10-29-2015,01:10 PM #12 lyte.iize View Profile View Forum Posts View Articles Join Date Oct 2015 Location Fresno/CA Posts 1 Re: Jets not https://www.swimuniversity.com/5-common-hot-tub-issues-solutions/

In Ground Spa Jets Not Working

Should I tell him to make it higher? Pingback: Is Buying A Used Hot Tub On Craigslist Or Ebay The Best Idea? | Pingback: Hot tub flow error causes and solutions Leave a Reply Cancel reply Your email address If the breaker does not trip after unplugging the pump, ozonator or blow, you’ve found the problem and you can now replace that component. It comes on for it's four cleaning cycles and FLO comes back on.

It works after each repair for about 10 minutes and FLO comes back on. DO NOT DISCONNECT IT COMPLETELY. You can solder a t'former with no issues. Hot Tub Air Lock Symptoms I was going to try what you say, makes perfect sense and so many agree.

I know this is an old post but it saved me repair cost. Test the water to check that this is the case. If the air is not purged within 2-3 minutes, turn the spa off, let the pump cool off, and try again. https://spapartsplus.com/update/docs/spu0114_Jets.html I have circulation pump and ozone.

It is important that you only loosen this coupling because the pressure generated by the pump will prevent you getting it back in place. Bathtub Jets Not Working Can't access the equipment? Q: My Spa Pump is Dead - No Noise, No Action! This is often the sign that the filters need to be cleaned or replaced.

Hot Tub Jets Weak

Marie leopold I just purchased an older hot tub from a friend. Everything froze. In Ground Spa Jets Not Working Gas Comparison More Hot tub low flow error causes and solutions……. Half Of Hot Tub Jets Not Working First, are other equipment items powered, are the indicator lights on?

You should hear air or see water coming from it once it's loose. Advanced Search Forum > Swimming Pool Care > Spas and Hot Tubs > Jets not working after fresh fill? Now I've pulled the board and have to get a new relay and solder it on. It should be a quarter turn past hand tight. -Jay Tracey July 6, 2016 at 11:18 pm We just filled our hot tub and the jets were working at first and Hot Tub Jets Won't Turn On

Find your filter. Ralph Sampson Yeah. This is something that is best left to the experts. Where the plumbing connects to the spa pump will be a big white union nut threaded onto the wet end of the motor.

Sometimes motors with bad bearings can last for months; however the loud noise will only get louder. Hot Tub Pump Not Working The heat light is off and the thermostat is set lower than the water temperature. Q: My Spa Pump Only Works on Low Speed A: When your 2-speed hot tub pump only works on low speed, and never kicks into high speed, there are four possible

Go find the plunger.

Some just had the one filter. Releasing an Air Lock From The Pump Area Remove front panel of spa (usually philips head screwdriver is needed) Locate large union nut connecting spa plumbing to motor Loosen nut on Now if during your initial attempts you see no increase in the amount of air bubbles coming out of the jets or worse no air bubbles at all coming out of the jets My Hot Tub Won't Turn On Originally Posted by spishex I make a lot of money every year around this time from people who are unable to diagnose and fix air locks, so hopefully this will reach

And about the heater and chasing the line to find the problem. If the the object is too large, you will sometimes need to remove the orifice and manually pull the object out of the jet. Keep in mind that there will soon be electricity near you. If it has, clean or change the filters.

I left out of town the next day and didn't come back for two days, when I noticed a storm had knocked my cover off and my tub was showing a Randy Simmons Yes. Repeat this process, using the lid like a plunger until water starts to come up at you from the filter housing. Any suggestions?

Can you access the equipment?

© Copyright 2017 philgiebler.com. All rights reserved.