Home > Hot Tub > Spa Motor Not Working

Spa Motor Not Working


Loosen but do not remove one of the plumbing unions on your pump until you see just a little water and listen for escaping air. The pool pump was running but sounded loud. How To Determine Why a Motor Won't Start or Shuts Off WRITTEN BY: Inyo Pools 4.33 out of 5 stars on 3 ratings (Click on a star to add your Disconnect the pump's electrical plug from the side of the control box.

Thanks inyopools Posted: 07/08/2016 14:32 PM Inyo Product Specialist bt - This is typically the symptom of a wrong voltage problem. All information is provided "AS IS." Website operating problems contact [email protected] I reinstalled the motor back in the system. If you have even the slightest doubt, call a spa technician or electrician before proceeding.

Hot Tub Motor Won't Start

Once this occurs the pump can then begin to move water through your system. If the impeller was jammed with something, changing the capacitor would have had absolutely no effect on it. No need to overtighten these as long as there is no water leaking. For this error, the instructions manual indicates that the drive was not able to start the motor after 3 attempts.

I leave the motor running from the opening in spring until I close the pool Sept Oct. Threads and overall size can vary greatly. Third, check your time clock or remote spa controller, if you have one, to make sure it is not over riding the switch you are using. 2 Speed Spa Pump Troubleshooting If you replace the Fuse and it pops again, you have an short in the wiring equipment of your spa.

Don't spend too much. Hot Tub Motor Hums But Won't Start Each time they are cleaned, they lose a bit more of their ability to trap small dirt and contaminants. If I shut off the timer switch and then back on, nothing happens. http://www.hottubworks.com/Troubleshooting/Pumps.php Maybe the capacitor on the pump went out?

Then, when I turned the power back on, the pump wouldn't start. Hot Tub Pump Making Noise If the motor is configured for 230V and has 115V coming in, it will shut down after running 3-5 minutes. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Check for undersized wiring.

Hot Tub Motor Hums But Won't Start

All rights reserved. check my blog Both Speeds Simultaneously If high and low speeds are operating simultaneously, then remove pump cord and then examine pump air switch for power. Hot Tub Motor Won't Start Disconnect the plumbing from the the inlet and outlet. Hot Tub Pump Just Hums I would recheck the wiring to and from the switch or possibly replace the switch.

Step 4 Motor gets hot and shuts down - Generally due to low voltage or being overloaded. Here is What You Need to Know The Jet Set - Identifying and Replacing Bathtub & Spa Jets Hot Tub Supplies Need discount hot tub parts ? Mike Posted: 07/10/2016 3:02 AM Hi,So it means the thermal overload protector cannot protect the pump from overvoltage? See this chart on Wire sizes. Hot Tub Circulation Pump Not Working

Davy Merino InTheSwim Blog Editor Posted in How To Pool Blog Posts Tagged Hot Tub Troubles, hot tubs, Spa Repair, spas permalink Post navigation ← Black Friday Pool Supply Clearance Remember to regularly check these components to make sure they are free from debris and anything that may damage them. If repeated attempts (hours apart) still cannot get pumps to prime, you can wait overnight and just let the spa sit. Geri al Kapat Bu video kullanılamıyor. İzleme SırasıSıraİzleme SırasıSıra Tümünü kaldırBağlantıyı kes The next video is startingstop Yükleniyor... İzleme Sırası Sıra __count__/__total__ How To Fix A Pool Or Spa Motor That

In a pinch, a pipe wrench can also be used, gently. Hot Tub Motor Capacitor Yükleniyor... Çalışıyor... Nut 3 Posted: 08/28/2016 8:51 AM I have a Pentair WhisperFlo WFE-4 pump.

Why do solar planes have many small propellers instead of fewer large ones?

Video kiralandığında oy verilebilir. Faulty Controls On older spa with air controls, the buttons can stick, the hoses can detach, or they can be found in disrepair or with holes. Don't use a screwdriver and hammer to loosen, if you can avoid it. No High Speed On Spa Pump Düşüncelerinizi paylaşmak için oturum açın.

Anonymous Posted: 09/24/2016 11:32 AM My pool pump motor won't start. If it's stuck, check that the impeller is not jammed with debris. You must be logged in to post a comment. The best way to loosen one of the pump unions to remove the air lock is with channel locks or large pliers.  If those are not available, this enterprising tech in

My original suspicion was that the wind and rain that blew the cover open on the timer box somehow shorted it out. Second, if the noise is a low pitched, grumbling noise, the pump could be starved for water. Second, is the union on top of the pump. If the voltage is right, then you need to change the pump motor entirely.

Just to be sure I loosened the outlet connector on the pump and water drained out, in hopes that any air would be released The control box unit has two fuses

© Copyright 2017 philgiebler.com. All rights reserved.