Loading...

Home > Sprinkler System > Sprinkler Not Working At All

Sprinkler Not Working At All

Contents

I discovered the Hunter Pro-C controller even has a "Quick Check" feature that helps in identifying potential shorts caused by faulty solenoids. Check the electrical connections to the zone valves on the controller, the common (or return) connection may be loose. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Ads for Typical Repair Parts: Advertisement (content continues below ad): (Amazon has lots more repair parts, for many brands, this is just a start! his comment is here

If the voltage falls below the manufacturer's range, replace the transformer. Does this potentially indicate an electical wiring connection problem at one of the valves? I found your ticket in our support system (looks like you were working with Kevin). Be sure the controller is in the off position (you don't need to shut off the power) and the water valves on the backflow device are turned off. https://www.bogleheads.org/forum/viewtopic.php?t=74106

Sprinkler System Not Working In All Zones

Let's make sure we are using the word "manual" in the same sense. Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". To replace it, label each wire that's connected to the controller with a piece of tape.

Requested Username: Please enter a valid username Username already exists Username cannot contain spaces or special characters Password: Please enter a password Forgot Your Password? Can you also send us some photos of your wiring to review to [email protected]? They all cant be bad. Sprinkler System Troubleshooting Solenoid Thanks again for your time with this.

Measure with a multimeter. Sprinkler System Won't Turn On section of line at the leak. Try that.

If there are wires connected to the “Sensor” terminal screws, there is a sensor on the irrigation system.

Replacement heads and other parts Tubing repair parts Band clamps Waterproof wire connectors Popular How-To Videos Email a Friend Send link to this project to a friend, along with a personal Hunter Sprinkler System Troubleshooting iScaper1 172,092 views 16:55 Loading more suggestions... Is there a rain sensor wired into the controller? If the controller, fuse and transformer check out OK, test the resistance “ohms” between the common terminal and the nonworking zone.

Sprinkler System Won't Turn On

Valve Cleaning and Repair If you've tested the controller and wires and they are OK, then the problem is with the valve itself.  You have two choices:  remove and replace the over here Another endorsement for Frank McCourt posted by someone who's location is Dodger Stadium! Sprinkler System Not Working In All Zones Or, if it has a circuit breaker reset button, press the button, then try the system again. None Of My Sprinkler Zones Are Working Did you open it manually.

Top Imperabo Posts: 1099 Joined: Fri Aug 29, 2008 1:00 am Quote Postby Imperabo » Mon May 09, 2011 8:33 am RMO87 wrote:I checked the water and it is still open. http://philgiebler.com/sprinkler-system/sprinkler-not-working-one-zone.html closed... I tried again to manually turn on each zone and nothing. You can test the wire very simply.  If the wires from the controller to the valve are disconnected from the valve reattach them to the valve solenoid now. Sprinkler System Troubleshooting No Water

The pipes are plastic and much simpler to repair than the plumbing in your house. We welcome your comments and suggestions. It's free! http://philgiebler.com/sprinkler-system/sprinkler-stations-not-working.html We'll get it figured out Thanks, Emil marknk8t 2015-03-16 16:42:26 UTC #3 I have the exact same problem.

If only one zone isn't working, the field wire is damaged. Sprinkler Zone Won't Turn On It should work correctly now. Turn the head counterclockwise to remove it from the riser.

http://www.toro.com/en-us/homeowner/do- ...

Loading... Remove the plastic screen basket, which serves as a filter, at the base of the head. Before filling in the hole and replacing the sod, set the desired sprinkler pattern (see “Reset the Spray Pattern,” below). Sprinkler System Troubleshooting Low Pressure Controller problems are very rare, it is much more likely the problem is a broken wire.  Do NOT try to test the controller by using a wire to create a short-circuit

Do you happen to have a rain sensor connected to the Iro? Does this potentially indicate an electical wiring connection problem at one of the valves? I'm curious if we have a wiring issue? http://philgiebler.com/sprinkler-system/sprinkler-station-not-working.html The correct voltage should be around 24 vac.

Make sure it is turned "on." Make sure you have allocated time to each zone, eg days and minutes it should run. Ryan Top soaring Posts: 1438 Joined: Sun Nov 18, 2007 9:09 am Location: North Central Florida Quote Postby soaring » Fri May 06, 2011 7:40 am RMO87 wrote:No rain sensor and Allow the head to make a few rotations, then make additional adjustments while the system is running.

Back to Top Low water pressure? I manually opened the valves and still no rotors are operating.

Install the new head, turning it tight with your hands. Has it rained lately? Note #2:  24 VAC does not feel good if you shock yourself with it, especially if you are wet.  Don't touch bare wires without rubber gloves on! Place the head in the canister so the nozzle is at the edge of the area to be watered.

Kevin jtkibler 2015-03-27 22:30:56 UTC #9 I have the same issue and will send in photos tonight. above the highest sprinkler head in the yard. Then I uninstalled all the wires and re-did them. You can adjust some head types by turning a slot at the top with a screwdriver.

And I am sure all the heads are not clogged. From: To: Use commas(,) to separate up to 5 emails.

© Copyright 2017 philgiebler.com. All rights reserved.