Home > Sprinkler System > Sprinkler Not Working

Sprinkler Not Working


There will be resistance due to the retraction spring, but the riser should move easily up and down without catching or hanging up. Requested Username: Please enter a valid username Username already exists Username cannot contain spaces or special characters Password: Please enter a password Forgot Your Password? Set the head in the canister. Loading... his comment is here

Welcome to the DoItYourself Forums! Thanks in advance! Then each of your zones should have a control. Sign in to add this video to a playlist. http://www.familyhandyman.com/landscaping/fixing-sprinkler-systems/view-all

Sprinkler System Won't Turn On

Touch a lead to each of the transformer terminals -- marked “24vac” -- on the controller. The water line problem is always located between the last working head and the first nonworking head. Check out the breathtaking lobby of this classic 1902 resort hotel. First, turn the top clockwise until it stops.

These units come with everything you need, you just pipe it to your system and plug it in. All rights reserved. Touch one of the leads to the common terminal -- marked with “c” or “com” -- and touch the other lead to the terminal for the zone that is not working. Sprinkler System Troubleshooting Low Pressure Check for excessive blow-by of the sprinkler riser.

Touch the leads to the common terminal and zone terminal. Sprinkler System Troubleshooting Solenoid If the system is plugged into a GFCI receptacle, press the GFCI reset button. We will not maintain any record of these emails. pop over to these guys If water is getting to it from the house, the heads in zone 1 should pop and start working (if you open the valve far enough).

There are a number of pumps sold through hardware and catalog stores that are called "sprinkler pumps", most of these are designed to run a single sprinkler head on a hose. Sprinkler System Zone Won't Turn Off Working... Using a square shovel, slice the sod into easy-to-remove pieces. The description needs to be more clear.

Sprinkler System Troubleshooting Solenoid

The sprinklers were not popping up, and when the sprinkler system was turned on the showers in the 2nd floor apartments stopped working! Is the main irrigation water supply open? Sprinkler System Won't Turn On To solve the problem, make sure the zone wires are firmly attached to the terminals in the controller, the transformer is plugged in, and the circuit breaker at the main panel None Of My Sprinkler Zones Are Working Top RMO87 Posts: 123 Joined: Fri Jan 18, 2008 9:11 am Location: Kansas City, MO Quote Postby RMO87 » Mon May 09, 2011 12:31 pm They are Hunter PGV valves.

Standard KY Jelly, purchase at any drug store in the feminine hygiene dept. http://philgiebler.com/sprinkler-system/sprinkler-not-working-one-zone.html Inside the control valve box, remove the wire connectors and disconnect the two wires on the defective solenoid from the common and field wires. To change a broken head, turn off the system and dig a 2-ft.-diameter hole around the head. Low water pressure will result in the sprinkler heads barely shooting water. Sprinkler System Troubleshooting No Water

This applies to all zones. Orbit Irrigation 442,402 views 3:29 How to replace sprinkler valves. - Duration: 8:42. If not, the controller or station module needs to be replaced. http://philgiebler.com/sprinkler-system/sprinkler-stations-not-working.html The steps above should have identified the problem and fixed it.

Insert the wires into the transformer terminals and tighten the screws to hold the wires in place. Hunter Sprinkler System Troubleshooting Use the time you save to plow the mines for the gold it takes to make quality sprinklers. Test the field wire first.

Get extra cows, and make cheese for your own consumption.

Note #2:  24 VAC does not feel good if you shock yourself with it, especially if you are wet.  Don't touch bare wires without rubber gloves on! Rinse the basket in a bucket of clean water, washing out the debris (Photo 2). The electrical lines are low voltage, so they're not hazardous. Sprinkler Zone Won't Turn On The pipes are plastic and much simpler to repair than the plumbing in your house.

Top sscritic Posts: 21858 Joined: Thu Sep 06, 2007 8:36 am Quote Postby sscritic » Mon May 09, 2011 10:55 am RMO87 wrote:I checked the water and it is still open. Powered by phpBB Forum Software © phpBB Limited Time: 0.368s | Queries: 20 | Peak Memory Usage: 21.25 MiB SFGate Home Guides by Demand Media News Sports Business A&E Be sure the controller is in the off position (you don't need to shut off the power) and the water valves on the backflow device are turned off. http://philgiebler.com/sprinkler-system/sprinkler-station-not-working.html Follow the same procedure to test the common wire.

Back to Top Tools & Materials Required Tools for this Project Have the necessary tools for this DIY project lined up

Skip navigation UploadSign inSearch Loading... Your cache administrator is webmaster. Remove the solenoid again.  Now remove the valve's lid or cap.  The lid or cap may screw off like a jar lid, or it may be held in place with screws.  I've tried manually activating a zone, using the programmed schedule, and resetting the controller, all with no luck.

Loading... Look at the “Sensor” terminals on the controller. Contact Us DoItYourself.com Mobile Site Privacy Statement Top All times are GMT -7. Copyright © Jess Stryker, 1997-2012.

Privacy Policy | Legal | Steam Subscriber Agreement View mobile website ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: The pressure on the top of the diaphragm is released through the use of an internal or external bleed. Close Yeah, keep it Undo Close This video is unavailable. Solution 2: Check fuse and transformer Test the transformer Test the transformer voltage by placing the multimeter leads on the transformer terminals marked “24 vac” with the transformer plugged in.

Next remove the wires for the common and the "lead" wire circuit to your valve from the controller terminals. If there is voltage in the range of 24VAC to 28VAC on the station wires, the wiring is good. There should be a green lid or lids in the lawn where the outside vacuum breaker is. Clean two sided white plastic filter in Rainbird valves with a toothbrush.

Use a slip coupling to repair the leak. All rights reserved. They can all be bad so it would logically be a electrical issue.

© Copyright 2017 philgiebler.com. All rights reserved.