Loading...

Home > Sprinkler System > Sprinkler Stations Not Working

Sprinkler Stations Not Working

Contents

Basic Electrical Tests If you don't have a valve actuator test unit, start by making yourself a home-made valve activator using three nine-volt batteries.  See my page with full instructions for If the three valves are new because you have added another zone or two then the mainline flow may be not enough to feed all demand required from the newly added You can test the wire very simply.  If the wires from the controller to the valve are disconnected from the valve reattach them to the valve solenoid now. iScaper1 132,700 views 7:07 Troubleshooting: Testing power to a sprinkler valve. - Duration: 2:02. his comment is here

Clogged heads may rise but fail to spray, not lower after watering, or produce an erratic spray pattern. I removed the old valves (15yrs) to dig down to main incoming line to the house. If it doesn't, the controller needs to be replaced. (If you don't get any voltage reading, see “Check Fuse and Transformer,” below.) Fortunately, controllers rarely go bad unless struck by lightning. How can I check for loose connections versus wire shortages.

Sprinkler System Not Working In All Zones

Insert the wires into the transformer terminals and tighten the screws to hold the wires in place. Pull the wires out of the terminals and through the hole in the bottom or side of the controller box. 4Run the wires of the new transformer through the hole into Replace it with an 18-gauge wire rated for underground burial.

Undo holia123 I tried to turn the solenoid, but couldn't do it by hand (it doesn't have a handle), but I could turn the bleeder screw and the back yard station Photo 2: Close-up of slip coupling A slip coupling easily expands and contracts to replace a damaged section of line. Is there voltage on the station wires at the valve? Sprinkler System Won't Turn On iScaper1 51,620 views 5:09 Sprinkler System Repair & Troubleshooting - Duration: 1:03:37.

If it's working, plug the transformer back in, turn the system off and test the transformer for voltage. Sprinkler System Troubleshooting Solenoid Quote Postby RMO87 » Thu May 05, 2011 3:58 pm My system (Hunter with six zones, three years old) has been open and used for about a month now this spring. Just wonder if the voltage is too high or not ? http://www.familyhandyman.com/landscaping/fixing-sprinkler-systems/view-all None of the 6 zone valves operate and it is unlikely they all failed at the same time.

Pretty easy to do. None Of My Sprinkler Zones Are Working Look at the controller display, if the “Sensor OFF” message is displayed, the sensor is activated and inhibiting the watering cycles. I heard that it could be the problem and it also could be easily replaced. You can try replacing the diaphragm and see if it fixes your problem but be very careful in doing it.

Sprinkler System Troubleshooting Solenoid

Privacy Policy Back to Top × Choose Your Language English - USA English - Metric Español Italiano Français Português Deutsch Türkçe Polski Русский العربية 中国/中华 Bogleheads.org Investing advice inspired by Jack http://www.hunterindustries.com/support/x-core-controller-not-starting-watering-cycle Aloha Like Bookmark February 18, 2012 at 10:47PM Thank you for reporting this comment. Sprinkler System Not Working In All Zones Thanks again for the suggestions! Sprinkler System Zone Won't Turn Off Undo irrigirl When you say station do you mean the timer/controller?

It didn't work out. this content section of line at the leak. COMPLEXITY Simple COST Under $20 Similar Projects Cutting Down a Tree Install an In-Ground Drainage System How to Remove a Tree Stump Painlessly Inexpensive Landscaping for Attractive Entryways The Best Garden If the zone turns on, the old field wire is bad. Sprinkler Zone Won't Turn On

Powered by phpBB Forum Software © phpBB Limited Time: 0.340s | Queries: 20 | Peak Memory Usage: 21.25 MiB Irrigation Tutorials You've found the web's mother lode of Broken sprinkler heads are easy to identify. Remove the screws that fasten the controller box to the wall, and take it down. 5Screw the new controller to the wall. weblink Maybe can help Like Bookmark June 30, 2014 at 1:59AM Thank you for reporting this comment.

Clean & Repair a Valve: Most people try to repair the valve rather than replace it.  I really think a repair is often easier at this stage.  If you do proceed Sprinkler System Troubleshooting Low Pressure Photo 3: Adjust the spray Adjust the watering range of the sprinkler head before installing it. Undo irrigirl2 When you say "put it on," do you mean just turned the water on, and this happened?

Next clean the little socket area in the valve lid that the solenoid screws into and make sure there aren't any sand grains or bits of plastic loose in that area. 

Top retcaveman Posts: 911 Joined: Wed Oct 21, 2009 8:12 pm Quote Postby retcaveman » Fri May 06, 2011 3:51 am Just a thought... Required Materials for this Project Avoid last-minute shopping trips by having all your materials ready ahead of time. JMHO Aloha Like Bookmark August 21, 2010 at 8:03PM Thank you for reporting this comment. Sprinkler System Troubleshooting No Water That's the only place I can think of, but I can't even get under those bushes, because they are covering the ground. :-( Like Bookmark August 30, 2010 at 1:54AM

Use a slip coupling to repair the leak. Replacing a valve:  Removing and replacing a valve can be a big job if the valve is fully installed.  Basically this is a swap out, take a photo of the old The valves open, sending water through the underground water line, which causes the sprinkler heads to pop up and spray. http://philgiebler.com/sprinkler-system/sprinkler-station-not-working.html How old is the controller.

I then took new valve and attached it to another stations wires and it works. If there is a minimum voltage of 19VAC on the station wiring at the valve and the valve operates manually, but still doesn’t activate using the controller, the solenoid may need Usually in irrigation box or they could be above ground. Top livesoft Posts: 49581 Joined: Thu Mar 01, 2007 8:00 pm Quote Postby livesoft » Fri May 06, 2011 9:32 am Now you know how customer support folks on a phone

Her previous jobs include reporter, photographer and editor for a weekly newspaper. So, from the picture from your link I finally understood what a solenoid is!!!! (Thank you, thank you!!). Calling in a professional could cost at least $100, even for a simple problem you can fix yourself in 10 minutes. Low water pressure will result in the sprinkler heads barely shooting water.

Twist the ends of the new solenoid wires onto the same common and field wires that the old solenoid was attached to (Photo 2). Ads for Typical Repair Parts: Advertisement (content continues below ad): (Amazon has lots more repair parts, for many brands, this is just a start! sprinklerdaddy 195,690 views 5:01 Inground Sprinklers - Bad Solenoid Diagnosis And Repair - Duration: 17:12. Does this potentially indicate an electical wiring connection problem at one of the valves?

The valves will turn on the sprinklers if turned manually. We are all walking around his yard and garden and the outside of his house and inside his garage looking for water lines, main valves, sprinkler valves, etc from cyberspace, while Basically it is a handle that needs to be opened up all the way then turned down 4-6 turns. The clock can work, but I think it is on a separate fuse from the valves.

If a single zone is not working, the problem is usually an electrical issue or a defective controller or solenoid.

© Copyright 2017 philgiebler.com. All rights reserved.