Home > Sprinkler System > Sprinkler System Not Working In All Zones

Sprinkler System Not Working In All Zones


JoeyS 2015-11-13 18:48:32 UTC #18 I was having the same issue with my Hunter Pro-C. If the zone turns on, the old field wire is bad. By sliding the Rain Sensor switch to the “Bypass” position you can over-ride the active sensor. Top sscritic Posts: 21858 Joined: Thu Sep 06, 2007 8:36 am Quote Postby sscritic » Mon May 09, 2011 10:55 am RMO87 wrote:I checked the water and it is still open. http://philgiebler.com/sprinkler-system/sprinkler-system-zones-not-working.html

I will look at your manual and post back. Replacement heads and other parts Tubing repair parts Band clamps Waterproof wire connectors Popular How-To Videos Email a Friend Send link to this project to a friend, along with a personal If the valve did not turn on any of the sprinklers, the water to the valves is still off. Replace it with a new section of line, making connections with standard couplings and band clamps. https://www.bogleheads.org/forum/viewtopic.php?t=74106

Sprinkler System Won't Turn On

Look for a series of sprinkler heads that aren't watering properly. The time now is 04:32 PM. The valves open, sending water through the underground water line, which causes the sprinkler heads to pop up and spray.

Top livesoft Posts: 49581 Joined: Thu Mar 01, 2007 8:00 pm Quote Postby livesoft » Fri May 06, 2011 9:32 am Now you know how customer support folks on a phone You can adjust some head types by turning a slot at the top with a screwdriver. I've tried manually activating a zone, using the programmed schedule, and resetting the controller, all with no luck. None Of My Sprinkler Zones Are Working I'll review and reply with a few other troubleshooting ideas.

Sorry that you are having issues with your sprinklers not running. Sprinkler System Troubleshooting Solenoid How to Unclog a Drain Reader's Digest Taste of Home Recipes © 2016 HOME SERVICE PUBLICATIONS, INC. Photo 2: Close-up of slip coupling A slip coupling easily expands and contracts to replace a damaged section of line.

Are you attempting to manually start a zone and having this issue?

This applies to all zones. Sprinkler Zone Not Working Just curious, were you aware you had a master valve before installing the Iro? No fuses, no broken sprinkler heads, no control boxes, no computers, no electrical mess, no pipes to worry about. Place a clamp on one of the line ends, insert the coupling, then tighten the clamp.

Sprinkler System Troubleshooting Solenoid

Working... http://sprinklerdoc.4t.com/allzone.htm Juan Sandoval Plumbing 191,011 views 3:22 Testing Sprinkler System Wiring - Duration: 5:09. Sprinkler System Won't Turn On Kids are good for that. Sprinkler Zone Won't Turn On Thanks again for your time with this.

No fuses, no broken sprinkler heads, no control boxes, no computers, no electrical mess, no pipes to worry about. this content Of course if no work has been done in this area then it probably isn't turned off but worth knowing where it is anyway. Sprinkler heads are factory tested to make sure they work. Does anyone have any other ideas as to what to check? Sprinkler System Troubleshooting No Water

Dirt sometimes gets inside sprinkler heads, causing them to clog up. If you can't pop the basket out with your fingers, pry it out with a flat-head screwdriver or pull it free with a pliers. Adjust the heads before installing them, then fine-tune them once they're in place with the sprinkler running. weblink Powered by vBulletin™ Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc.

During the repair I use the technique of "voltage drop testing", which is designed to find high dynamic resistance connections. Sprinkler System Zone Won't Turn Off Typically the multimeter should register between 24 and 28 volts. Typically the ohms should register between 20 and 60.

above the highest sprinkler head in the yard.

From your product manual:For fast manual operation, a quick 1⁄2 turn of the solenoid allows water to bleed off of the top of the diaphragm and, as a result, opens the emil 2015-11-16 05:30:31 UTC #19 JoeyS: Flipping on the master valve switch in the app made it work. @JoeyS, great to hear! If only one zone isn't working, the field wire is damaged. Sprinkler System Troubleshooting Low Pressure Photo 2: Clean the screen basket Remove the screen basket from the bottom of the head, then clean it with water.

Also great point about "do's and dont's" provided up front. Loading... Photo 2: Splice in new pipe Cut out the damaged section of line. http://philgiebler.com/sprinkler-system/sprinkler-system-not-working.html Controller may be set for Even Days and today is the 21st) Is the controller set on Interval watering days?

Any misadventure resulting from your attempt to repair your sprinkler system is your responsibility. If you get 24 vac goto # 13, if not goto #8 #8 Make sure there are no rain or freeze sensors activated, check controller fuse. If fuse is good Sprinkler heads are installed only hand-tight, but after being in the ground for several years, they may require the use of wrenches to unscrew. Sign up today for FREE and become part of The Family Handyman community of DIYers.

Or vehicles may have compressed the soil and collapsed the line. Replace it with an 18-gauge wire rated for underground burial. Top BigD53 Posts: 1042 Joined: Sat Jul 21, 2007 7:47 pm Quote Postby BigD53 » Fri May 06, 2011 9:51 am What happen to the old fashioned way of using a Turn the head counterclockwise to remove it from the riser.

Is the Watering Start Time programmed with correct time of day (i.e. Category Science & Technology License Standard YouTube License Show more Show less Loading... I have moved wires around again, but this time it didn't work. Don't use Teflon tape or joint compound on the riser threads.

Published on Aug 13, 2012I demonstrate a diagnostic algorithm for workup of a defective solenoid as a cause of failure to water a sprinkler zone in a home irrigation system. I found your ticket in our support system (looks like you were working with Kevin). If you have any questions at any time you can email me #1 I know this sounds stupid, but make sure the water is on, open main valve ( At the valve box, check the resistance of each coil to find the bad one. "I'm not so much concerned about the return on my money as the return of my

Privacy Policy Back to Top × Choose Your Language English - USA English - Metric Español Italiano Français Português Deutsch Türkçe Polski Русский العربية 中国/中华 ERROR The requested URL could not http://www.hunterindustries.com/Resourc ... Is the main irrigation water supply open? Next we will check the master valve and the field wiring to the master valve, as this is the only solution left.) #10 You will need a multi-meter thats reads

© Copyright 2017 philgiebler.com. All rights reserved.