Loading...

Home > Sprinkler System > Sprinkler System Not Working In One Zone

Sprinkler System Not Working In One Zone

Contents

Düşüncelerinizi paylaşmak için oturum açın. Clogged heads may rise but fail to spray, not lower after watering, or produce an erratic spray pattern. If voltage their. Text and Images by Jess Stryker unless noted. http://philgiebler.com/sprinkler-system/sprinkler-system-1-zone-not-working.html

when zones don't operate, it can only be a few things. It doesn't matter which lead goes to which terminal. Follow 5 answers 5 Report Abuse Are you sure you want to delete this answer? deliriousga HVAC 5 12-29-2006 07:04 PM Login User Name Remember Me?

Sprinkler System Not Working In All Zones

If a single zone is not working, the problem is usually an electrical issue or a defective controller or solenoid. These problems are harder to find and often require a lot of digging. Turn the valve on the horizontal pipe first, then the vertical pipe valve. Here's a list.

You don't need special skills to make the repairs, but you'll need a multimeter to diagnose electrical problems.

Figure A: How a Sprinkler System Works The controller sends a signal Solution 2: Find and repair leaks Photo 1: Install a slip coupling Cut out the damaged section of line and replace it with a slip coupling. Since Zone 3 is located in the same location as the other two simply remove ( and tag) the wires from zone one(1) and then attach the wires from Zone three(3) None Of My Sprinkler Zones Are Working Adjustment methods vary.

Look for signs of leaking water, such as water bubbling up from the soil when the sprinklers are running, a depression in the ground, or a very wet area. Looks some may be legacy and dead? Clean & Repair a Valve: Most people try to repair the valve rather than replace it.  I really think a repair is often easier at this stage.  If you do proceed To change a broken head, turn off the system and dig a 2-ft.-diameter hole around the head.

more than likely you have a bad solenoid. Sprinkler System Troubleshooting Low Pressure Advertisement (content continues below ad): If the valve is more than a couple years old you might want to purchase a repair kit for the valve make and model (see bottom Before filling in the hole and replacing the sod, set the desired sprinkler pattern (see “Reset the Spray Pattern,” below). Please upload a file larger than 100x100 pixels We are experiencing some problems, please try again.

Sprinkler System Troubleshooting Solenoid

Hard to diagnose by yourself. have a peek here It should work correctly now. Sprinkler System Not Working In All Zones Note: a lot of anti-siphon valves are not properly installed.  Even sprinkler installation companies don't use the care they should to insure correct installation, and a incorrect installation may be the Sprinkler System Zone Won't Turn Off Then turn off the water and clean out any screen in the manifold.

Standard KY Jelly, purchase at any drug store in the feminine hygiene dept. this content Rule And/Or Policy Violation Join Date Oct 2007 State MI Posts 176 There is no substitute for a job done right!! 04-22-08,05:27 PM #7 Bob M Member Join Date Oct 2000 Note #2:  24 VAC does not feel good if you shock yourself with it, especially if you are wet.  Don't touch bare wires without rubber gloves on! If the voltage is less than 24, the transformer is defective. 3To replace the transformer, use a Phillips screwdriver to loosen the screws holding the transformer wires in the terminals. Sprinkler System Won't Turn On

No special skills needed. Rain sensors conserve water by preventing the system from running when the ground is already saturated and doesn't need additional watering. Don't be intimidated by the prospect of working on a system that involves both plumbing and electricity. http://philgiebler.com/sprinkler-system/sprinkler-system-zone-not-working.html Turn on the sprinklers at the controller.

Check this out carefully. Sprinkler Zone Low Pressure Photo 2: Reconnect the wires Connect the two wires on the new solenoid to the common wire and a field wire, using waterproof connectors. It's free!

iScaper1 51.620 görüntüleme 5:09 Starting up your sprinkler system in the spring - Süre: 1:36.

Clean two sided white plastic filter in Rainbird valves with a toothbrush. All rights reserved. Member benefits: Get a FREE Traditional Bookcase Project Plan Sign up for FREE DIY newsletters Join us Newsletters Shop DIY Books DIY Tip Genius App Free Product Info Promotions Login Join Sprinkler System Troubleshooting No Water References (1) The Family Handyman: Fixing Sprinkler Systems About the Author Melody Lee holds a degree in landscape design, is a Florida Master Gardener, and has more than 30 years of

if you do not know where the valves are you should calla professional company in. Place a clamp on one of the line ends, insert the coupling, then tighten the clamp. Just a thought to pass on. check over here Cut it Again!

Login Register Unread posts Unreplied threads Threads of the last 24 hours Advanced Search Advanced Search SPRINKLER TALK FORUM - You Got Questions, We've Got Answers Forum Members Help The link Contact Us DoItYourself.com Mobile Site Privacy Statement Top All times are GMT -7. If it still doesn't turn on, make sure the outlet that the power transformer is plugged into is working by plugging in a power tool. Dig down to the “riser” (the vertical pipe that branches off the main line) which is connected to the sprinkler head.

© Copyright 2017 philgiebler.com. All rights reserved.