Home > Sprinkler System > Sprinkler System Zones Not Working

Sprinkler System Zones Not Working


Top RMO87 Posts: 123 Joined: Fri Jan 18, 2008 9:11 am Location: Kansas City, MO Quote Postby RMO87 » Mon May 09, 2011 12:31 pm They are Hunter PGV valves. I've seen your massive sprinkler systems at Dodger Stadium in use. Did you open the valves by using a screwdriver in your hand to turn the release screw on the physical valve? WatermasterIrr 38.579 visualizações 5:06 Sprinkler Valve Troubleshooting - Duração: 2:05. this content

Top BigD53 Posts: 1042 Joined: Sat Jul 21, 2007 7:47 pm Quote Postby BigD53 » Fri May 06, 2011 9:51 am What happen to the old fashioned way of using a when you are doing this you are simply bypassing the timer. I manually turned, by hand, the solenoid counter clockwise. Solution 1: Turn on valves at backflow device Check the valves Check the valves on the backflow device to make sure they're open. http://homeguides.sfgate.com/fix-one-zone-lawn-sprinkler-system-isnt-working-94411.html

Sprinkler System Not Working In All Zones

Top rwwoods Posts: 1312 Joined: Thu Jun 07, 2007 7:54 pm Location: The Villages, Florida Quote Postby rwwoods » Thu May 05, 2011 7:05 pm My friend's system stoped because of Cut a new section of pipe to replace the damaged one. hon-Valves Loosen the screw. Using this method I isolated and replaced the manifold and so far ( knock on wood) no problems.

Tom Glander 80.596 visualizações 2:05 Repair a Hunter PGV 101G Sprinkler Valve - Duração: 5:31. I suddenly have a problem with the system not working. Adicionar a Quer assistir de novo mais tarde? None Of My Sprinkler Zones Are Working Fila de exibiçãoFilaFila de exibiçãoFila Remover todosDesconectar The next video is startingstop Carregando...

Set the multimeter to “voltage” and turn on the zone with the controller. Sprinkler System Troubleshooting Solenoid They are spread out around your lawn and should be mostly level with the ground and visible. The valves open, sending water through the underground water line, which causes the sprinkler heads to pop up and spray. Using your voltmeter, check the voltage at each station terminal screw when that station is active.

We service Lake Murray, Irmo, and the Town of Lexington and look forward to being of service - Schedule an Appointment by calling (803)331-5323, email us at [email protected] , follow us Sprinkler System Troubleshooting Low Pressure Repair damaged wires If the ohms reading between the common terminal and nonworking zone terminal is too high (it's sometimes an infinity reading), the problem is a severed or bad wire Twist the two wire connectors off the wires from the solenoid to the common and field wires. Carregando...

Sprinkler System Troubleshooting Solenoid

Top sscritic Posts: 21858 Joined: Thu Sep 06, 2007 8:36 am Quote Postby sscritic » Thu May 05, 2011 4:24 pm Did you manually open one of the valves? http://www.doityourself.com/forum/lawns-landscaping-outdoor-decor/342258-home-sprinklers-2-6-zones-not-working.html Touch one of the leads to the common terminal -- marked with “c” or “com” -- and touch the other lead to the terminal for the zone that is not working. Sprinkler System Not Working In All Zones If the voltage is lower than the recommendation in the owner’s manual, but is above 0, the controller is defective. 3To replace the controller, fold a piece of tape around each Sprinkler System Zone Won't Turn Off John A · 9 years ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report Abuse Determine whether it is electrical, or mechanical.

Rule And/Or Policy Violation Join Date Oct 2007 State MI Posts 176 There is no substitute for a job done right!! 04-22-08,05:27 PM #7 Bob M Member Join Date Oct 2000 news Test the field wire first. Powered by vBulletin™ Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Photo 3: Adjust the spray Adjust the watering range of the sprinkler head before installing it. Sprinkler System Won't Turn On

Top retcaveman Posts: 911 Joined: Wed Oct 21, 2009 8:12 pm Quote Postby retcaveman » Fri May 06, 2011 3:51 am Just a thought... Solution 3: Replace defective valve Photo 1: Replace the solenoid Disconnect the wires and unscrew the defective solenoid from the control valve. If you have a rain sensor, you can turn it off...or just wait till things dry out a little. have a peek at these guys Answer Questions Magnetic auto controler ser #f05299592?

it294w.pdfDid you check that the flow control valve was open? (It doesn't make sense that someone would go around and close them all, but who knows?)When fine tuning the system, adjust Sprinkler System Troubleshooting No Water Check Solenoid and Wiring 1If the controller, fuse, and transformer are working correctly, use the multimeter to check the ohms between the common terminal and the terminal for the zone that I've been dragging a hose around for the past 56 years.

The transformer terminals are marked “24 vac.” A 24-voltage transformer should normally test between 24 and 28 volts.

Be sure to buy the same type of head that you're replacing. Here's a list. Categoria Ciência e tecnologia Licença Licença padrão do YouTube Mostrar mais Mostrar menos Carregando... Sprinkler Zone Low Pressure If you’re not sure what valve it is, make a note of what color wire is hooked up to #4 on the controller and then look for the valve with that

I've seen your massive sprinkler systems at Dodger Stadium in use. In attempting to start it up this year, I found that zone 1 is inactive. Take the head apart by holding the bottom of the canister and turning the top of the head counterclockwise. http://philgiebler.com/sprinkler-system/sprinkler-system-not-working.html Top Imperabo Posts: 1099 Joined: Fri Aug 29, 2008 1:00 am Quote Postby Imperabo » Mon May 09, 2011 8:33 am RMO87 wrote:I checked the water and it is still open.

By the way to winterize is a snap. Is there a rain sensor wired into the controller? That wire is connected to the #4 valve solenoid, and it’s at this point that I see a lot of bad connections, generally because people twist wires together without using water By sliding the Rain Sensor switch to the “Bypass” position you can over-ride the active sensor.

© Copyright 2017 philgiebler.com. All rights reserved.